 |
TECHNICKÝ LIST 27.12.2006 |
|
ValttiTeho - Wood Finish |
|
|
| TYP | Semi-matt alkyd-oil based, slightly thixotropic, opaque wood finish for exterior surfaces. | |
| VHODNOSŤ | New, sawn or planed wood surfaces, impregnated wood and also previously oil-painted or stained wood surfaces. With Valtti Teho you can change darker stained surfaces in good condition to lighter colours. Not suitable for floors. |
|
| PRÍKLADY POUŽITIA | Exterior walls, covering boards, window frames, doors, garden furniture etc. | |
| TECHNICKÉ ÚDAJE | ||
 4  12 |
||
| Bázy farieb | A a C | |
| Rozsah odtieňov | White base paint A can be used as such or tinted (Color card for exterior paints).
C base is colourless and must always be tinted before use. |
|
| Stupne lesklosti | 4. Polomat | |
| Výdatnosť | Smooth wood: 8-12 m²/l per coat. Sawn wood: 4-8 m²/l per coat. Actual spreading rates will depend upon many factors including texture, porosity and moisture content of the substrate. |
|
| Veľkosti balenia | 0.9 l, 2.7 l, 9 l a 18 l | |
| Riedidlo | White Spirit 1050 | |
| Aplikačná metóda | Brush or spray application | |
| Doba schnutia pri 23°C a 50% relatívnej vlhkosti vzduchu | Dry after approx. 12 hours and recoatable after 24 hours. Low temperatures and high humidity will extend drying times. | |
| Sušina | Approx. 42%, depending on the colour. | |
| Hustota | 1.1 kg/l, ISO 2811. | |
| Skladovanie | Unaffected by cold storage. Badly closed or short cans and/or tinted products do not withstand long storage. | |
| NÁVOD NA POUŽITIE | ||
| Podmienky aplikácie | All surfaces to be painted must be dry, the moisture content of the wood below 20 %, the temperature of the air at least +5 °C, and the relative humidity of the air below 80 % during painting work and drying.
Finishing must be done before evening dew. The paint film must be dry, because humidity will turn the fresh surface matt. |
|
| Príprava | Unpainted surface
Remove all dirt, dust, wax, rust and loose wooden material. Prime bare wood always with Valtti Base at an early building stage.Treat potential rust spots with Rostex Super Metal Primer. Seal knots with Knotting Lacquer (Oksalakka) after removing resin. A priming coat of Valtti Base should be applied to all exterior wood which has not been pre-treated or vacuum impregnated with an approved wood preservative. Apply liberally on end-grain. Use recommended Tikkurila fillers for filling cracks, nail holes, blemishes, etc. Previously painted surface Remove loose paint with a scraper and brush the surface with steel brush. Wash down surfaces affected by mould with Mould Removal (Homeenpoisto) or Super Clean solution according to instructions. Prime bare wood always with Valtti Base. Note: Discoloration of paint especially noticeable within light colours may occur over knots and resinous areas present in the wood. Particular attention with regards to preparation should be given to wood such as Oak, Teak, Cedar, Douglas Fir, Mahogany and Idigbo, etc., which contain oil and water-soluble tannin which may impair the drying, hardening or adhesion of surface coatings and discolour the finished surface. |
|
| Natieranie | Reserve enough paint in one can for a uniform surface to avoid colour differences. Stir the paint thoroughly before use. Apply two coats on new surfaces and 1-2 coats on old surfaces. Treat end-grains extra carefully. Valtti Teho can be thinned with White Spirit 1050, if necessary. | |
| Čistenie náradia | Clean immediately after use with white spirit 1050 or with Tikkurila Pensselipesu (Tool Cleaner) | |
| Údržba | Depending on exposure and elevation, one coat of Valtti Teho is normally sufficient after 5 years. | |
| EU VOC 2004/42/EC - hraničné hodnoty | (cat A/e) 500g/l(2007)/ 400g/l(2010) | |
| ZDRAVOTNÁ A BEZPEČNOSTNÁ KLASIFIKÁCIA | Harmful, Xn Contains: Naphtha, hydrotreated heavy (aliphatic hydrocarbon solvent), and tolylfluanid (0,9 w-%) SYTTYVÄÄ. HAITALLISTA VESIELIÖILLE, VOI AIHEUTTAA PITKÄAIKAISIA HAITTAVAIKUTUKSIA VESIYMPÄRISTÖSSÄ. Huolehdittava hyvästä ilmanvaihdosta. Vältettävä liuotehöyryn/ruiskutussumun hengittämistä. Varottava kemikaalin joutumista iholle. Ei saa tyhjentää viemäriin. Jos ainetta on nielty, hakeuduttava heti lääkärin hoitoon ja näytettävä tämä pakkaus tai etiketti. Säilytettävä lasten ulottumattomissa. Sisältää tolyylifluanidia, etyylimetyyliketoksiimia ja kobolttioktoaattia. Voi aiheuttaa allergisen reaktion. A Material Safety Data Sheet is available at request.Material Safety Data Sheet - ValttiTeho | |
 Škodlivý |
||
| OCHRANA ŽIVOTNÉHO PROSTREDIA A ZNEŠKODNENIE ODPADU | Empty cans should be recycled or disposed of in accordance with local regulations. Liquid waste should be destroyed according to the local regulations. NOTE! Cleaning cloths or sanding dust containing the product can create fire by auto-ignition and should be stored in water before disposal, or be dried outdoors or incinerated immediately. | |
| DOPRAVA | VAK/ADR 3 III | |
| mli011106/lko141106/akk221206/565- | ||
Horeuvedené informácie, založené na laboratórnych testoch a praktických skúsenostiach, sú platné od dátumu uvedeného na technickom liste výrobkuKvalita produktov je zabezpečovaná našim operačným systémom, podľa požiadaviek ISO 9001 a ISO 14001.Výrobca nemôže byť zodpovedný za žiadne škody, ktoré vznikli použitím výrobku bez dodržania inštrukcií alebo za nevhodným účelom.
